In the box

• CCU (Course computer unit)
• ECU (Electronic control unit)
• ECU power cable
• ECU to CCU interconnect cable
• Steering actuator
• Throttle actuator
• Autopilot Remote
• Documentation

• Autopilot remote

• Physical dimensions (W x H x D): 6.0” x 2.0” x 1.3” (15.2 x 5.2 x 3.2 cm)

• Weight: 3.8 oz (109 g) without batteries

• Display type: Sunlight-visible, transflective memory-in-pixel (MIP)

• Display size: 1.2” (3.0 cm) diameter

• Display resolution: 240 x 240 pixels

• Power: 2 x AA batteries (sold separately)

• ECU 14

One of the main components of your autopilot system, the Electronic Control Unit (ECU) controls the actuators based on information received from the Course Computer Unit (CCU).

• Dimensions: 6.9” x 5.6” x 2.6” (17.5 x 14.2 x 6.5 cm)

• Supply voltage range: 10 to 32 volts

• Operating temperature range: -20° to 70° C

• Typical power consumption: 1 to 2 amps average depending on weather conditions

• Water rating: IPX7

• Steering Actuator

This mechanical linear actuator mounts through the tilt tube of your kicker motor and is driven by the autopilot system to provide precise steering control.

• Dimensions:

  • Motor side: Extends 4” (10.3 cm) from end of tilt tube

  • Motor: 2.5” (6.2 cm) diameter

  • Overall length: Closed 17.5” (44.5 cm); Extended 25.3” (64.4 cm)

• Operating temperature range: -20° to 70° C

• Water rating: IPX7

• Throttle Actuator

Install under your engine cover and connect to the existing throttle linkage to add electronic throttle control via your autopilot system.

• Dimensions: 6.0” x 2.5” x 1.1” (15.1 x 5.9 x 2.8 cm)

• Operating temperature range: 0° to 70° C

• Water rating: IPX6
  

Garmin Reactor 40 Kicker Engine Compatibility

• Throttle control is designed for tiller configured outboards only. Compatibility for remote throttle control configurations may require customized installation.

Manuals

REACTOR 40 KICKER ENGINE COMPATIBILITY

The Reactor 40 Kicker Autopilot is currently compatible with the following engines.

NOTE: The outboard motors listed below are compatible only if:

• The outboard has a tiller handle. Outboards without a tiller handle may work with custom installation not supported by Garmin
• The outboard has a tilt tube. Outboards without a standard tilt tube are not compatible.  Aftermarket “bolt on” tilt tubes are not supported (incorrectly positions steering actuator)

¹  Garmin requires replacement of the mild steel tilt tubes supplied by Yamaha and Honda with our stainless steel tilt tube.  This can be ordered as a kit or as an accessory of R40 Kicker (see accessories on Garmin.com). Mild steel tubes from Yamaha and Honda are more susceptible to corrosion which leads to damage of the R40 Kicker steering actuator. 

² For the purposes of Reactor 40 Kicker installation, consider Mercury and Tohatsu outboards to be the same.

**The price is subject to change at anytime without any notice.  We are not responsible for any typographical errors.  Any products can be cancelled from sale at any time.

** All Products sold here are Brand New unless specified Otherwise and come with Full Manufacturer's Warranty

WARNING: This product can expose you to chemicals including Di-n-hexyl Phthalate (DnHP) which is known to the State of California to cause reproductive harm, and Vinyl Chloride which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. __________________________________________________________________________________________

__________________________________________________________________________________________