icom M510BB Black Box VHF with HM195GB CommandMic
Model: M510 BB 21 USA
Icom’s M510BB is perfect for boats that need AIS receive functionality without
taking up precious helm space. The supplied CommandMic™ provides all the safety
and communication functions for commercial and leisure boaters.
The M510BB consists of a CommandMic™ and black box RF unit. Use the CommandMic™
for all operations including DSC. Install the RF unit out of sight, place up to
60 ft (18.3 m)* away from the CommandMic™.
Add up to two additional CommandMic™ microphones for boats requiring two or
three comms stations. Extend communication points around the boat including the
cockpit, fly bridge, and tower. Access the intercom functions for one-to-all or
one-to-one communications on the boat.
The M510BB includes an integrated AIS receiver, perfect for remote station
information via the CommandMic™, or integrated into the NMEA 2000® bus to
display radar and chart plotter information on an MFD (Multi-Function Display).
In addition to the conveniently located DSC button on the back of every
CommandMic™, the M510BB introduces a dedicated DSC Remote Control (EN 300 338-8
compatible) terminal, allowing a connection to an external device to centralize
emergency communications control.
The M510BB has a last call voice recording function automatically saves up to
two minutes of an incoming call.
The NMEA 2000® network provides plug-and-play data communication to
inter-connect other marine equipment such as an MFD (Multi-Function Display).
The radio can send AIS, GNSS (GPS) position, DSC call, and radio channels to
other equipment.
On the back of every CommandMic™ is a conveniently located DSC button. Once
triggered, the M510BB transmits a DSC alert signal to nearby vessels with the
MMSI* and GPS location of your vessel. *MMSI number must be obtained and
programmed for each vessel/radio.
The built-in 15W amplifier increases the audio output of an external hailer
speaker. The one-way RX hailer function enables you to broadcast radio traffic
through the hailer speaker to listen to radio traffic on the deck or tower. You
can also sound foghorn patterns from the hailer speaker.
The Active Noise Cancelling function digitally removes background noise from
transmitting and receiving audio to provide clear communications in noisy
maritime environments.
Specifications
General
|
Usable
channels
|
USA, INT,
CAN, WX channels
|
Power
supply requirement
|
13.8 V DC
nominal (11.7 ~ 15.9 V DC) (Negative ground)
|
Current
drain (at 13.8 V DC)
|
TX Max.
power - 5.5 A Max.
RX Max. audio - 1.5 A (One CommandMic™) 4.5 A (Three CommandMic™ and RX
hailer)
|
Operating
temperature range
|
—20°C ~
60°C, —4?F ~ 140?F
|
Antenna
impedance
|
50 ohm
nominal
|
Weight
(approx.)
|
RF unit -
890 g; 2 lb
CommandMic™ - 400 g; 14.1 oz
|
Transmitter
|
Output
power (at 13.8V DC)
|
25 W, 1 W
(High, Low)
|
Max.
frequency deviation
|
±5 kHz
|
Frequency
tolerance
|
±0.5 kHz
|
Spurious
emissions
|
Less than
—70 dBc (High power), Less than —56 dBc (Low power)
|
Residual
modulation
|
More than
40 dB
|
Adjacent
channel power
|
More than
70 dB
|
Receiver
|
Sensitivity
FM (at 12dB SINAD)
|
0.22 ?V
typical
|
Sensitivity
DSC (at 1% BER)
|
—7 dB? emf
typical
|
Adjacent
channel selectivity FM
|
More than
70 dB
|
Adjacent
channel selectivity DSC (1% BER)
|
More than
73 dBµ emf
|
Spurious
response FM
|
More than
70 dB
|
Spurious
response DSC (1% BER)
|
More than
73 dB? emf
|
Intermodulation FM
|
More than
75 dB
|
Intermodulation DSC (1% BER)
|
More than
68 dBµ emf
|
Hum and
noise
|
More than
40 dB
|
What's in the Box:
- IC-M510BB
- DC power cable (2 m)
- Microphone Hanger
- Connection cable, OPC-1540
(6.1 m, 20 ft)
- CommandMic™, HM-195G
- Connector cap
- Mounting base
Documentation
Comparison
ICOM510BB21USA_Comparison.pdf
Data Sheet
ICOM510BB21USA_DataSheet.pdf