Vetus Ignition Protected Thruster
A bow thruster delivers a side directional thrust force. In order to ensure the best performance under all sorts of weather and water conditions, the bow thruster should be able to provide a thrust force which is suitable, or rather: sufficient, for the boat in which it has been installed. The applied moment of the thrust force - which means to say: the position of the tunnel in the bow - is of prime importance for the bow thruster's efficiency. The further forward the bow thruster is positioned, the greater will be the efficiency.
|
 |  | |  | VETUS Bow Thruster 121 Lbf (55 Kgf), Tube Diameter 5 29/32", Ignition Protected, 3Kw, 4HP, BOW5512Di
Brand New with Factory
Warranty
Ship only via Ground Freight Rate. No Flat Rate. | | VETUS Bow Thruster 165 Lbf (75 Kgf), Tube Diameter 7 9/32", Ignition Protected, 4.4Kw, 6HP, BOW7512Di
Brand New with Factory
Warranty
Ship only via Ground Freight Rate. No Flat Rate. | | |  | VETUS Bow Thruster 210 Lbf (95 Kgf), Tube Diameter 7 9/32", Ignition Protected, 5.3Kw, 7.5HP, BOW9512Di
Brand New with Factory
Warranty
Ship only via Ground Freight Rate. No Flat Rate. | |
|
Selecting the correct Bow Thruster
A bow thruster delivers a side directional thrust force.
In order to ensure the best performance under all sorts of weather and water
conditions, the bow thruster should be able to provide a thrust force which
is suitable, or rather: sufficient, for the boat in which it has been
installed. The applied moment of the thrust force - which means to say: the
position of the tunnel in the bow - is of prime importance for the bow
thruster's efficiency. The further forward the bow thruster is positioned,
the greater will be the efficiency. |
The force applied by the wind onto the boat is determined by the factors:
wind speed, angle of wind attack and lateral wind draft area
of the boat.
- The Wind Pressure
When the wind speed increases, the wind pressure increases
quadraticallly!
For wind pressure 'P', the formula reads: P = 1/2p × V²
(l bf/sq.ft)
p (rho) represents the specific mass of air and 'V' stands
for the
velocity of the air in ft/s.
The table below will give you an impression of wind speeds and the
resulting wind pressures. It will not be possible to counter completely
the adverse effect of winds of 40 knots or more. But, in such cases, the
bow thruster will still "lend a strong helping hand".
- The Wind-Draft of the Boat
The forces applied by the wind onto the boat can be determined by
multiplying the wind pressure by the wind draft area. The wind draft area
is determined by the shape and the dimensions of the superstructure. Also
the wind angle is playing its part. The worst situation is created if the
wind is at 90 degrees to the boat. However, due to the shape of the
superstructure, which is mostly more or less streamlined, a reduction
factor may be applied to the wind draft area, before calculating the wind
pressure resulting from the wind speed. This reduction factor may
generally be set at 0.75.
- The Torque
The torque is determined by multiplying the wind force by the distance (A)
between the center of effort* of the wind and the center of rotation** of
the boat. Assuming that the wind force is amidships and assuming as well
that the boat will tend to turn at the transom, the torque, caused by the
wind force, is calculated by multiplying the wind force by half of the
boat's length.
* - Dependent upon the shape of the boat's superstructure, the
center of effort may be positioned more forward or more aft.
** - The center of rotation of the boat may be positioned more forward,
dependent upon the shape of the underwater section.
- The Thrust Force
The bow thruster is required to apply a countering thrust force, which is
at least equal to the thrust force applied by the wind. The required
thrust force of the bow thruster may now be calculated by dividing the
torque by the distance between the center of the bow thruster and the
pivot point of the boat.
Wind Speed - Wind Pressure Chart
Wind Speed
knots |
Description |
Wind Speed
ft/s |
Wind pressure lbf/sq.ft. |
10 -
16
16 - 22
22 - 28
28 - 34
34 - 40 |
moderate breeze
fresh breeze
strong breeze
near breeze
gale |
17 -
27
27 - 37
37 - 47
47 - 57
57 - 67 |
0.40 -
1
1 - 1.9
1.9 - 3.1
3.1 - 4.6
4.6 - 6.3 |
Calculation example
| The boat has an
overall length of 36 ft and the lateral wind draft measures 190 sq.ft.
It is required that the bow can still be controlled easily when a wind
force of 20 knots applies. At a wind force of 20 knots, the wind
pressure is:
p = 1.0 to 1.9 lbf/sq.ft i.e.p. (average) 1.45 lbf/sq.ft.
The required torque reads:
T = windpressure x wind draft x reduction factor x
distance center of effort to pivot point, (=appr. half the ship's
length)
T = 1.45 lbf/sq.ft x 190 sq/ft x 0,75 x 36 ft/2 =
3719 ft.lbs.
The required Thrust Force is calculated as
follows:
F = Torque/distance between the center of bow
thruster and the pivot of the boat
= 3719 ft/lb / 34.5 ft = 107.8 lb
The VETUS bow thruster which is most suitable for
this particular vessel is the 121 lbf model.
Always bear in mind that the effective
performance of a bow thruster will vary with each particular boat, as
the displacement, the shape of the underwater section and the
positioning of the bow thruster will always be variable factor. |
|
| |
|
|
|
